2026-09-21 · KeXinMaterials 编辑团队
PP vs ABS vs PC 材料对比:B2B 硬壳防护箱采购指南 2026
PP、ABS、PC 是 B2B 防护箱三大主流材料。PP 最轻 + 最便宜。ABS 中端。PC 最强 + 最贵。2026 B2B 采购对比。
材料性能对比
PP, ABS, and PC differ significantly in density, impact strength, temperature range, UV resistance, and chemical resistance. Material choice depends on application + spec requirements.
PP (polypropylene): density 0.90 g/cm³, lightest. Impact strength (Izod) 100-150 J/m. Temperature range -20C to +100C. UV resistance moderate (UV stabilizer required). Chemical resistance excellent (acids, bases, solvents). Tensile strength 25-40 MPa.
ABS (acrylonitrile butadiene styrene): density 1.04 g/cm³, mid-range. Impact strength 200-400 J/m. Temperature range -40C to +85C. UV resistance low (yellowing over time). Chemical resistance moderate. Tensile strength 35-50 MPa.
PC (polycarbonate): density 1.20 g/cm³, heaviest. Impact strength 600-900 J/m (highest). Temperature range -40C to +120C. UV resistance moderate (UV stabilizer required). Chemical resistance poor (solvents attack). Tensile strength 55-75 MPa.
PP+GF (glass fiber reinforced PP): density 1.05-1.20 g/cm³, mid-range. Impact strength 80-100 J/m (slightly lower than pure PP). Temperature range -30C to +110C. UV resistance moderate. Glass fiber content 10-30%.
成本 + 起订量 + 交期
PP is cheapest, PC is most expensive. Cost difference affects B2B procurement decisions.
PP: USD 1.20-1.80/kg. Cheapest material. Easy to mold, low tool wear.
PP+GF (glass fiber): USD 1.50-2.50/kg. Mid-range. Higher strength than pure PP.
ABS: USD 1.80-2.50/kg. Mid-range. Common in consumer electronics.
PC: USD 3.00-5.00/kg. Most expensive. Specialty applications.
PP/PC blend: USD 2.50-3.50/kg. Mid-range. Combines PP + PC properties.
Tooling cost: PP tooling cheapest (lower temperatures, lower pressure). PC tooling most expensive (high temperatures, high pressure).
MOQ: PP 50-100 cases. ABS 100-200 cases. PC 200-500 cases (due to higher cost).
注塑考虑
PP, ABS, PC differ significantly in injection molding parameters. Material choice affects tooling cost, cycle time, and product quality.
PP molding: melt temperature 200-260C, mold 20-30C, injection pressure 60-100 MPa. Cycle time 15-25 seconds. Easy to mold, low tool wear.
ABS molding: melt temperature 220-260C, mold 40-80C, injection pressure 70-100 MPa. Cycle time 20-30 seconds. Slightly more challenging than PP.
PC molding: melt temperature 280-320C, mold 80-120C, injection pressure 80-140 MPa. Cycle time 30-45 seconds. Requires precision tooling + high temperatures.
Tool wear: PP lowest (mild). ABS moderate. PC highest (abrasive + high temperature). PC tools require hardened steel (HRC 60+) and frequent maintenance.
Shrinkage: PP 1.5-2.5%. ABS 0.3-0.8%. PC 0.5-0.7%. PP requires more precise shrinkage compensation.
B2B 应用建议
Different B2B applications favor different materials. Below is the 2026 recommendation.
Photography / broadcast (camera cases): PP+GF for lightweight + adequate strength. PP+GF 30% for premium cases.
Military / tactical (NSN procurement): PP+GF for impact resistance + cost-effectiveness. Berry Amendment compliant materials.
Drone (1-5 kg payload): PP+GF for lightweight + impact resistance. Cost-effective for frequent replacement.
Medical (cleanability + compliance): ABS or PP for cleanability. Anti-microbial additive.
Industrial / measurement (5+ kg instrument): PP+GF for impact resistance + cost. Standard.
Aerospace (AS9100 + UL94 V-0): PC for strength + flame resistance. Premium cost.
Marine (IP68 + salt fog): PP or PP+GF for UV + salt water resistance.
Cold chain (2-8°C refrigerated): PP or PP+GF for low temperature toughness.
Consumer (camera / outdoor / Pelican alternative): ABS or PP for cost-effectiveness.
紫外 + 耐化学性
UV and chemical resistance differ across PP, ABS, PC. Important for outdoor / industrial use.
UV resistance: PP moderate (UV stabilizer required for outdoor). ABS low (yellows over 6-12 months outdoor). PC moderate (UV stabilizer required for outdoor).
UV stabilizer additive: HALS (hindered amine light stabilizer) 0.5-1.5%. Carbon black 0.5-2% for black color. UV absorber 0.3-0.5% for transparent.
Chemical resistance: PP excellent (most acids, bases, solvents). ABS moderate (some solvents attack). PC poor (solvents like acetone, toluene attack).
Salt water: PP excellent (used for marine). ABS moderate. PC poor (becomes brittle).
Hydrocarbon (oil, gasoline): PP excellent. ABS moderate. PC poor (stress cracking).
Acid: PP excellent. ABS moderate. PC poor (concentrated acid attacks).
温度 + 机械性能
Temperature range and mechanical properties are key for industrial / extreme environment cases.
Low temperature toughness: PP -20C, ABS -40C (better), PC -40C (best). For cold chain (-20C deployment), PC or ABS preferred over PP.
High temperature: PP 100C, ABS 85C, PC 120C. For hot industrial deployment (foundry, oven, etc.), PC preferred.
Tensile strength: PC 55-75 MPa (highest), ABS 35-50 MPa (mid), PP 25-40 MPa (lowest). For load-bearing applications, PC preferred.
Flexural modulus: PC 2300 MPa (highest stiffness), ABS 2000 MPa, PP 1500 MPa. For rigid cases, PC > ABS > PP.
Impact strength: PC 600-900 J/m (highest, including low temperature), ABS 200-400 J/m, PP 100-150 J/m. For impact-critical, PC > ABS > PP.
可持续性 + 可回收性
Sustainability and recyclability differ across PP, ABS, PC. Important for EU CSRD + US SEC ESG reporting.
PP recyclability: high. Mono-PP cases can be recycled as PP stream. Recycled PP (rPP) 30-50% blend available.
ABS recyclability: moderate. ABS recycling requires separation from other plastics. Mixed ABS quality issues.
PC recyclability: low. PC recycling requires separation from other plastics. Yellowing limits recycling cycles.
Carbon footprint: PP 1.5-2.5 kgCO2e/kg, ABS 3.0-4.0 kgCO2e/kg, PC 4.0-6.0 kgCO2e/kg. PP lowest carbon footprint.
EU CSRD + US SEC: Scope 3 supply chain emissions reporting. Recyclability data required.
B2B recommendation: PP or PP+GF for sustainable case procurement. Mono-PP design for end-of-life recyclability.
成本优化策略
Material cost can be optimized by material choice, filler additives, and recycled content.
Use PP for cost-effective standard cases. 30-50% cost saving vs ABS or PC for non-critical applications.
Use PP+GF for premium cases with higher impact strength. Slightly higher cost vs pure PP.
Use ABS only when PP cannot meet spec (temperature, UV, impact). 30-50% cost premium vs PP.
Use PC only for extreme applications (aerospace, ultra-cold, ultra-high impact). 2-3x cost vs PP.
Recycled content: rPP 30-50% blend available. -5-15% cost vs virgin PP. Maintains 70-90% mechanical properties.
Calcium carbonate filler: 10-20% loading. -5-10% cost vs virgin PP. Slight property trade-off.
核心要点
- PP:USD 1.20-1.80/kg,最轻,优异耐化学性,可持续
- ABS:USD 1.80-2.50/kg,中端,良好低温韧性,常见消费品
- PC:USD 3.00-5.00/kg,最重,最高冲击强度 + 温度范围
- PP+GF:USD 1.50-2.50/kg,中端,玻璃纤维增强强度
- B2B 默认:大多数箱用 PP+GF;低温用 ABS;航空航天用 PC
常见问题
哪种材料最适合防护箱?
PP 是大多数 B2B 防护箱的默认最佳材料。最轻(0.90 g/cm³),最便宜(USD 1.20-1.80/kg),优异耐化学性,可持续(单 PP 回收)。
ABS 还是 PC 适合箱?
PC 冲击强度更高(600-900 J/m vs ABS 200-400 J/m),温度范围更宽。但 PC 比 ABS 贵 2-3 倍。
PP 比 ABS 便宜吗?
是的。PP 比 ABS 便宜 30-50%。PP 的模具也便宜。
什么是玻璃纤维增强 PP?
PP+GF(玻璃纤维增强聚丙烯)是含 10-30% 玻璃纤维的 PP。
PP 抗紫外吗?
PP 有中等抗紫外性。无 UV 稳定剂时,PP 在 12-24 个月内户外降解。
PP 和 PE 塑料的区别?
PP vs PE:PP 熔点更高(160°C vs 130°C),拉伸强度更高,耐化学性更好。
PP 箱能回收吗?
可以。PP 箱可回收。单 PP 设计(全 PP 外壳 + PP 铰链 + PP 锁扣 + PP 泡沫盘)可作为 PP 流回收。